Heidenhain MANUALplus 4110 User Manual Page 483
- Page / 550
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
HEIDENHAIN MANUALplus 4110 483
9.3 ICP Example "Matrix"
9.3 ICP Example "Matrix"
This example illustrates how to machine a matrix using the ICP
programming feature. The individual working steps for machining the
ICP contour and integrating the contour into ICP cycles are based on
the workpiece drawing.
In the process described below, you create an ICP contour description
and a cycle program for parts production.
The machining operation is performed with the "ICP cutting
transverse" cycle.
Required tools
Roughing tool:
Position T1
WO = 1 Tool orientation
A = 93° Setting angle
B = 55° Nose angle
R = 0.8 Tool radius
Finishing tool:
Position T2
WO = 1 Tool orientation
A = 93° Setting angle
B = 55° Nose angle
R = 0.5 Tool radius
Sequence of working steps
Clamp a workpiece blank (diameter 95 mm, length 100 mm).
Machine setup
– Define the workpiece zero point.
– Measure the tool dimensions.
Switch to "Teach-in" mode.
Enter the positioning cycles for tool change.
ICP contour programming.
Integrate the ICP contour in the roughing and finishing cycles.
- MANUALplus 1
- Functions 2
- Contents 3
- 2 Basics of Operation 31 6
- 4 Cycle Programming 79 8
- 5 ICP Programming 241 11
- 6 DIN Programming 277 12
- 7 Tool Management Mode 411 16
- 9 Examples 457 17
- 10 Tables and Overviews 523 17
- Introduction and 19
- Fundamentals 19
- 1.1 The MANUALplus 20
- 1.2 Features 21
- 1.3 MANUALplus Design 22
- 1.4 Axis Designations and 25
- Coordinate System 25
- Absolute coordinates 26
- Incremental coordinates 26
- Polar coordinates 26
- 1.5 Machine Reference Points 27
- 1.6 Tool Dimensions 28
- Basics of Operation 31
- 2.1 The MANUALplus Screen 32
- 2.1 The MANUALplus 32
- 2.2 Operation and Data Input 33
- 2.3 Error Messages 36
- 2.4 Explanation of Terms 39
- Machine Mode of Operation 41
- 3.1 Machine Mode of Operation 42
- 3.2 Switch-On / Switch-Off 43
- 3.3 Machine Data 46
- 3.4 Machine Setup 50
- 3.5 Setting up Tools 54
- 3.6 Manual Mode 60
- 3.7 Teach-In Mode 62
- 3.8 Program Run Mode 63
- 3.9 Graphic Simulation 68
- 3.10 Time Calculation 74
- 3.11 Program Management 75
- 3.13 Inch Mode 78
- Cycle Programming 79
- 4.1 Working with Cycles 80
- 4.2 Workpiece Blank Cycles 85
- 4.3 Single Cut Cycles 88
- 4.4 Roughing Cycles 100
- 4.5 Recessing cycles 129
- 4.6 Thread and Undercut 162
- Check the thread 164
- Press Last cut 164
- Activate Cycle Start 164
- Thread cycle (longitudinal) 165
- Tapered thread 168
- API thread 170
- Recut (longitudinal) thread 172
- Recut tapered thread 176
- Recut API thread 178
- Undercut DIN 76 180
- Undercut DIN 509 E 182
- Undercut DIN 509 F 184
- 4.7 Drilling Cycles 190
- 4.8 Milling Cycles 201
- 4.9 Drilling/Milling Patterns 227
- 4.10 DIN Cycles 239
- ICP Programming 241
- 5.1 ICP Contours 242
- 5.2 Editing ICP Contours 243
- 5.3 Importing of DXF Contours 250
- Contours 254
- Adding a contour element 257
- Deleting a contour element 257
- Superimposing form elements 259
- Entering form elements 263
- B chamfer width—or 264
- B rounding radius 264
- F special feed 264
- Undercuts, turning contour 265
- Entering lines on the face 269
- Lateral Surface 272
- DIN Programming 277
- 6.1 DIN Programming 278
- 6.2 Editing DIN Programs 281
- Chuck part, cylinder/tube G20 288
- Workpiece blank contour G21 289
- 6.4 Tool Positioning without 290
- Machining 290
- Tool change point G14 291
- Movements 292
- Speed limitation G26/G126 297
- Interrupted feed G64 297
- Feed per tooth G193 298
- Feed per revolution G95/G195 298
- Spindle speed G97/G197 299
- Compensation 300
- G40: Switch off TRC/MCRC 301
- G41/G42: Switch on TRC/MCRC 301
- 6.8 Compensation Values 302
- 6.9 Zero Point Shifts 305
- 6.10 Oversizes 308
- Contour definition 310
- End of cycle G80 310
- K oversize Z (default: 0) 311
- Contour finishing G89 318
- 6.12 Simple Turning Cycles 319
- 6.13 Recessing Cycles 324
- 6.14 Recess-Turning Cycles 331
- 6.15 Thread Cycles 335
- 6.16 Undercut Cycles 344
- 6.17 Parting Cycle 353
- 6.18 Drilling Cycles 354
- 6.19 C-Axis Commands 359
- 6.20 Face Machining 360
- Reference diameter G120 371
- Z end point 372
- C end angle 372
- Helical-slot milling G798 379
- Z center point 380
- R radius of circle 380
- 6.22 Pattern Machining 383
- 6.23 Other G Functions 391
- 6.24 Set T, S, F 392
- 6.24 Set T, S, F 392
- 6.26 Programming Variables 396
- WHILE (program repeat) 402
- 6.28 Variables as Address 403
- Parameters 403
- 6.29 Subprograms 406
- 6.30 M Functions 408
- Tool Management 411
- 7.1 Tool Management Mode of 412
- Operation 412
- Tool life management 413
- 7.2 Tool Organization 414
- 7.3 Tool Texts 416
- 7.4 Tool Data 418
- 7.5 Tool Data— 426
- Supplementary 426
- Organization Mode of 429
- 8.1 Organization Mode of 430
- 8.2 Parameters 431
- 8.3 Transfer 441
- 8.4 Service and Diagnosis 453
- Examples 457
- 9.1 Working with MANUALplus 458
- Contour element 3 511
- 9.6 DIN Programming Example 516
- "Threaded Stud" 516
- 9.7 DIN Programming Example 519
- "Milling Cycle" 519
- Tables and Overviews 523
- 10.1 Thread Pitch 524
- 10.2 Undercut Parameters 525
- 10.3 Technical Information 528
- 10.4 Peripheral Interface 532
- Overview of G functions 543
- Overview of G functions 543
- Overview of Cycles 547
Related products and manuals for Equipment Heidenhain MANUALplus 4110
Equipment Heidenhain MANUALplus 4110 User Manual
(550 pages)
(550 pages)
Equipment Heidenhain MANUALplus 4110 User Manual
(552 pages)
(552 pages)
Equipment Heidenhain MANUALplus 4110 User Manual
(550 pages)
(550 pages)
(120 pages)
(119 pages)
Equipment Heidenhain MANUALplus 4110 User Manual
(553 pages)
(553 pages)
© 2020, manymanuals.com. All rights reserved. | 0.106 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals