Heidenhain TNC 640 (34059x-01) Cycle programming User Manual Page 291
- Page / 549
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
HEIDENHAIN TNC 640 291
13.6 TURN SHOULDER, LONGITUDINAL EXTENDED (Cycle 812)
Finishing cycle run
If the starting point lies in the area to be machined, the TNC positions
the tool beforehand to set-up clearance in the Z coordinate.
1 The TNC runs the paraxial infeed motion at rapid traverse.
2 The TNC finishes the finished part contour (contour starting point
to contour end point) at the defined feed rate Q505.
3 The TNC returns the tool to set-up clearance at the defined feed
rate.
4 The TNC positions the tool back at rapid traverse to the cycle
starting point.
Please note while programming:
Also refer to the fundamentals of turning cycles (see page 286).
Program a positioning block to a safe position with radius
compensation R0 before the cycle call.
The tool position at cycle call (cycle starting point) affects
the area to be machined.
Also refer to the fundamentals of turning cycles (see
page 286).
- User’s Manual 1
- Cycle Programming 1
- Software options 5
- Intended place of operation 7
- Legal information 7
- Contents 9
- HEIDENHAIN TNC 640 11 11
- 1.1 Introduction ..... 38 11
- 2 Using Fixed Cycles ..... 41 12
- 13 Cycles: Turning ..... 279 24
- Fundamentals / 37
- Overviews 37
- 1.1 Introduction 38
- 1.2 Available Cycle Groups 39
- Using Fixed Cycles 41
- 2.1 Working with Fixed Cycles 42
- Entering PATTERN DEF 47
- Using PATTERN DEF 47
- Defining a single row 49
- Defining a single pattern 50
- Defining individual frames 51
- Defining a full circle 52
- Defining a pitch circle 53
- 2.3 Point Tables 54
- Fixed Cycles: Drilling 59
- 3.1 Fundamentals 60
- 3.2 CENTERING (Cycle 240 61
- DIN/ISO: G240) 61
- 3.3 DRILLING (Cycle 200) 63
- 3.4 REAMING (Cycle 201 65
- DIN/ISO: G201) 65
- 3.5 BORING (Cycle 202 67
- DIN/ISO: G202) 67
- 3.6 UNIVERSAL DRILLING 71
- (Cycle 203, DIN/ISO: G203) 71
- 3.7 BACK BORING (Cycle 204 75
- DIN/ISO: G204) 75
- 3.8 UNIVERSAL PECKING 79
- (Cycle 205, DIN/ISO: G205) 79
- 3.9 BORE MILLING (Cycle 208) 83
- (Cycle 241, DIN/ISO: G241) 86
- 3.11 Programming Examples 89
- Fixed Cycles: Tapping / 93
- Thread Milling 93
- 4.1 Fundamentals 94
- Tap Holder (Cycle 206 95
- DIN/ISO: G206) 95
- DIN/ISO: G207) 97
- 4.3 RIGID TAPPING without a 97
- Floating Tap Holder NEW 97
- (Cycle 207, DIN/ISO: G207) 97
- 4.4 TAPPING WITH CHIP 100
- BREAKING (Cycle 209 100
- DIN/ISO: G209) 100
- Cycle parameters 102
- Prerequisites 103
- DIN/ISO: G262) 105
- COUNTERSINKING (Cycle 263 108
- DIN/ISO: G263) 108
- 4.7 THREAD MILLING / 108
- 4.8 THREAD DRILLING/MILLING 112
- (Cycle 264, DIN/ISO: G264) 112
- Q359 (incremental): 115
- 4.9 HELICAL THREAD 116
- DRILLING/MILLING (Cycle 265 116
- DIN/ISO: G265) 116
- 4.10 OUTSIDE THREAD MILLING 120
- (Cycle 267, DIN/ISO: G267) 120
- 4.11 Programming Examples 124
- Fixed Cycles: Pocket 127
- Milling / Stud Milling / 127
- Slot Milling 127
- 5.1 Fundamentals 128
- 5.2 RECTANGULAR POCKET 129
- (Cycle 251, DIN/ISO: G251) 129
- DIN/ISO: G252) 134
- 5.4 SLOT MILLING (Cycle 253 138
- DIN/ISO: G253) 138
- DIN/ISO: G254) 143
- 5.6 RECTANGULAR STUD 148
- (Cycle 256, DIN/ISO: G256) 148
- DIN/ISO: G257) 152
- 5.8 Programming Examples 156
- Fixed Cycles: 159
- Pattern Definitions 159
- 6.1 Fundamentals 160
- DIN/ISO: G220) 161
- 6.3 CARTESIAN PATTERN 164
- (Cycle 221, DIN/ISO: G221) 164
- 6.4 Programming Examples 166
- Contour Pocket 169
- 7.1 SL Cycles 170
- DIN/ISO: G37) 172
- 7.3 Overlapping Contours 173
- 7.4 CONTOUR DATA (Cycle 20 177
- DIN/ISO: G120) 177
- DIN/ISO: G121) 179
- 7.6 ROUGH-OUT (Cycle 22 181
- DIN/ISO: G122) 181
- DIN/ISO: G123) 184
- DIN/ISO: G124) 186
- 7.9 CONTOUR TRAIN (Cycle 25 188
- DIN/ISO: G125) 188
- 7.10 Programming Examples 191
- Cylindrical Surface 197
- 8.1 Fundamentals 198
- DIN/ISO: G127, Software 199
- Option 1) 199
- Software-Option 1) 202
- (Cycle 28, DIN/ISO: G128 202
- Cycle run 205
- 8.5 Programming Examples 208
- Fixed Cycles: Contour 213
- Pocket with Contour 213
- Fundamentals 214
- Defining contour descriptions 216
- Overlapping contours 218
- Multipass Milling 227
- 10.1 Fundamentals 228
- 10.2 MULTIPASS MILLING 229
- (Cycle 230, DIN/ISO: G230) 229
- DIN/ISO: G232) 235
- 10.5 Programming Examples 240
- Cycles: Coordinate 243
- Transformations 243
- 11.1 Fundamentals 244
- 11.2 DATUM SHIFT (Cycle 7 245
- DIN/ISO: G54) 245
- 11.3 DATUM SHIFT with Datum 246
- Editing mode of operation 249
- Configuring the datum table 250
- To exit a datum table 250
- Status displays 250
- DIN/ISO: G247) 251
- 11.5 MIRROR IMAGE (Cycle 8 252
- DIN/ISO: G28) 252
- 11.6 ROTATION (Cycle 10 254
- DIN/ISO: G73) 254
- 11.7 SCALING (Cycle 11 256
- DIN/ISO: G72) 256
- 11.8 AXIS-SPECIFIC SCALING 258
- (Cycle 26) 258
- DIN/ISO: G80, Software 260
- Resetting 261
- Workspace monitoring 264
- 11.10 Programming Examples 266
- Cycles: 269
- Special Functions 269
- 12.1 Fundamentals 270
- 12.2 DWELL TIME (Cycle 9 271
- DIN/ISO: G04) 271
- 12.3 PROGRAM CALL (Cycle 12 272
- DIN/ISO: G39) 272
- 12.4 SPINDLE ORIENTATION 274
- (Cycle 13, DIN/ISO: G36) 274
- 12.5 TOLERANCE (Cycle 32 275
- DIN/ISO: G62) 275
- CAM TNCPP 276
- Cycles: Turning 279
- 13.1 Turning Cycles 280
- (Software Option 50) 280
- Working with turning cycles 282
- 13.2 ADAPT ROTARY COORDINATE 283
- SYSTEM (Cycle 800) 283
- 13.3 RESET ROTARY COORDINATE 285
- SYSTEM (Cycle 801) 285
- 13.4 Fundamentals of Turning 286
- 13.5 TURN SHOULDER 287
- LONGITUDINAL (Cycle 811) 287
- Finishing cycle run 288
- 13.6 TURN SHOULDER 290
- LONGITUDINAL EXTENDED 290
- (Cycle 812) 290
- 13.7 TURN, LONGITUDINAL 294
- PLUNGE (Cycle 813) 294
- 13.8 TURN, LONGITUDINAL 298
- PLUNGE EXTENDED 298
- (Cycle 814) 298
- 13.9 TURN CONTOUR 302
- LONGITUDINAL (Cycle 810) 302
- 13.10 TURN CONTOUR-PARALLEL 306
- (Cycle 815) 306
- 13.11 TURN SHOULDER FACE 310
- (Cycle 821) 310
- 13.12 TURN SHOULDER FACE 313
- EXTENDED (Cycle 822) 313
- (Cycle 823) 317
- EXTENDED (Cycle 824) 321
- 13.15 TURN CONTOUR 325
- TRANSVERSE (Cycle 820) 325
- 13.16 RADIAL RECESSING 329
- (Cycle 861) 329
- 13.17 RADIAL RECESSING 332
- EXTENDED (Cycle 862) 332
- 13.18 RECESSING CONTOUR 336
- RADIAL (Cycle 860) 336
- Application 340
- Roughing cycle run 340
- 13.20 AXIAL RECESSING 343
- EXTENDED (Cycle 872) 343
- (Cycle 870) 347
- 13.22 LONGITUDINAL THREAD 351
- (Cycle 831) 351
- 13.23 THREAD EXTENDED 355
- (Cycle 832) 355
- 13.24 CONTOUR-PARALLEL 359
- THREAD (Cycle 830) 359
- 13.25 Example program 363
- Using Touch Probe 367
- Touch Probe Cycles 368
- Executing touch probe cycles 373
- 14.3 Touch Probe Table 374
- Touch Probe Cycles: 377
- Automatic Measurement 377
- Misalignment 377
- 15.1 Fundamentals 378
- DIN/ISO: G400) 380
- 15.3 BASIC ROTATION from Two 383
- Q268 Q270 387
- DIN/ISO: G403) 390
- 15.6 SET BASIC ROTATION 392
- (Cycle 404, DIN/ISO: G404) 392
- (Cycle 405, DIN/ISO: G405) 394
- Automatic Datum 399
- 16.1 Fundamentals 400
- 16.2 SLOT CENTER REF PT 403
- (Cycle 408, DIN/ISO: G408) 403
- 16.3 DATUM RIDGE CENTER 407
- (Cycle 409, DIN/ISO: G409) 407
- SET_UP(TCHPROBE.TP) 420
- (Cycle 417, DIN/ISO: G417) 439
- 16.13 DATUM IN ONE AXIS 445
- (Cycle 419, DIN/ISO: G419) 445
- 0 BEGIN PGM CYC413 MM 448
- 1 TOOL CALL 69 Z 448
- Automatic Workpiece 453
- Inspection 453
- 17.1 Fundamentals 454
- 17.2 REF. PLANE (Cycle 0 460
- DIN/ISO: G55) 460
- 17.3 POLAR REFERENCE PLANE 461
- (Cycle 1) 461
- DIN/ISO: G420) 463
- 17.9 MEASURE INSIDE WIDTH 482
- (Cycle 425, DIN/ISO: G425) 482
- 17.10 MEASURE RIDGE WIDTH 485
- (Cycle 426, DIN/ISO: G426) 485
- 17.11 MEASURE COORDINATE 488
- (Cycle 427, DIN/ISO: G427) 488
- 17.14 Programming Examples 498
- 18.1 Fundamentals 504
- 18.2 MEASURING (Cycle 3) 505
- Automatic Kinematics 507
- Measurement 507
- Overview 508
- 19.2 Prerequisites 509
- DIN/ISO: G450; Option) 510
- Log function 511
- Notes on data management 512
- 19.4 MEASURE KINEMATICS 513
- (Cycle 451, DIN/ISO: G451; 513
- Positioning direction 515
- Notes on the accuracy 518
- Backlash 519
- Various modes (Q406) 524
- Automatic Tool 527
- 20.1 Fundamentals 528
- DIN/ISO: G480) 533
- (Cycle 31 or 481 534
- DIN/ISO: G481) 534
- (Cycle 32 or 482 536
- DIN/ISO: G482) 536
- Radius (Cycle 33 or 483 538
- DIN/ISO: G483) 538
- Overview 541
- Touch probes from HEIDENHAIN 549
Related products and manuals for Equipment Heidenhain TNC 640 (34059x-01) Cycle programming
(549 pages)
(549 pages)
(547 pages)
(531 pages)
(519 pages)
(678 pages)© 2020, manymanuals.com. All rights reserved. | 0.037 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals