Heidenhain TNC 640 (34059x-01) Cycle programming User Manual Page 231
- Page / 549
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
HEIDENHAIN TNC 640 231
10.3 RULED SURFACE (Cycle 231, DIN/ISO: G231)
10.3 RULED SURFACE (Cycle 231,
DIN/ISO: G231)
Cycle run
1 From the current position, the TNC positions the tool in a linear 3-D
movement to the starting point 1.
2 The tool subsequently advances to the stopping point 2 at the feed
rate for milling.
3 From this point, the tool moves at rapid traverse FMAX by the tool
diameter in the positive tool axis direction, and then back to
starting point 1.
4 At the starting point 1 the TNC moves the tool back to the last
traversed Z value.
5 Then the TNC moves the tool in all three axes from point 1 in the
direction of point 4 to the next line.
6 From this point, the tool moves to the stopping point on this pass.
The TNC calculates the end point from point 2 and a movement in
the direction of point 3.
7 Multipass milling is repeated until the programmed surface has
been completed.
8 At the end of the cycle, the tool is positioned above the highest
programmed point in the spindle axis, offset by the tool diameter.
X
Y
Z
1
2
3
4
X
Y
Z
1
2
3
4
- User’s Manual 1
- Cycle Programming 1
- Software options 5
- Intended place of operation 7
- Legal information 7
- Contents 9
- HEIDENHAIN TNC 640 11 11
- 1.1 Introduction ..... 38 11
- 2 Using Fixed Cycles ..... 41 12
- 13 Cycles: Turning ..... 279 24
- Fundamentals / 37
- Overviews 37
- 1.1 Introduction 38
- 1.2 Available Cycle Groups 39
- Using Fixed Cycles 41
- 2.1 Working with Fixed Cycles 42
- Entering PATTERN DEF 47
- Using PATTERN DEF 47
- Defining a single row 49
- Defining a single pattern 50
- Defining individual frames 51
- Defining a full circle 52
- Defining a pitch circle 53
- 2.3 Point Tables 54
- Fixed Cycles: Drilling 59
- 3.1 Fundamentals 60
- 3.2 CENTERING (Cycle 240 61
- DIN/ISO: G240) 61
- 3.3 DRILLING (Cycle 200) 63
- 3.4 REAMING (Cycle 201 65
- DIN/ISO: G201) 65
- 3.5 BORING (Cycle 202 67
- DIN/ISO: G202) 67
- 3.6 UNIVERSAL DRILLING 71
- (Cycle 203, DIN/ISO: G203) 71
- 3.7 BACK BORING (Cycle 204 75
- DIN/ISO: G204) 75
- 3.8 UNIVERSAL PECKING 79
- (Cycle 205, DIN/ISO: G205) 79
- 3.9 BORE MILLING (Cycle 208) 83
- (Cycle 241, DIN/ISO: G241) 86
- 3.11 Programming Examples 89
- Fixed Cycles: Tapping / 93
- Thread Milling 93
- 4.1 Fundamentals 94
- Tap Holder (Cycle 206 95
- DIN/ISO: G206) 95
- DIN/ISO: G207) 97
- 4.3 RIGID TAPPING without a 97
- Floating Tap Holder NEW 97
- (Cycle 207, DIN/ISO: G207) 97
- 4.4 TAPPING WITH CHIP 100
- BREAKING (Cycle 209 100
- DIN/ISO: G209) 100
- Cycle parameters 102
- Prerequisites 103
- DIN/ISO: G262) 105
- COUNTERSINKING (Cycle 263 108
- DIN/ISO: G263) 108
- 4.7 THREAD MILLING / 108
- 4.8 THREAD DRILLING/MILLING 112
- (Cycle 264, DIN/ISO: G264) 112
- Q359 (incremental): 115
- 4.9 HELICAL THREAD 116
- DRILLING/MILLING (Cycle 265 116
- DIN/ISO: G265) 116
- 4.10 OUTSIDE THREAD MILLING 120
- (Cycle 267, DIN/ISO: G267) 120
- 4.11 Programming Examples 124
- Fixed Cycles: Pocket 127
- Milling / Stud Milling / 127
- Slot Milling 127
- 5.1 Fundamentals 128
- 5.2 RECTANGULAR POCKET 129
- (Cycle 251, DIN/ISO: G251) 129
- DIN/ISO: G252) 134
- 5.4 SLOT MILLING (Cycle 253 138
- DIN/ISO: G253) 138
- DIN/ISO: G254) 143
- 5.6 RECTANGULAR STUD 148
- (Cycle 256, DIN/ISO: G256) 148
- DIN/ISO: G257) 152
- 5.8 Programming Examples 156
- Fixed Cycles: 159
- Pattern Definitions 159
- 6.1 Fundamentals 160
- DIN/ISO: G220) 161
- 6.3 CARTESIAN PATTERN 164
- (Cycle 221, DIN/ISO: G221) 164
- 6.4 Programming Examples 166
- Contour Pocket 169
- 7.1 SL Cycles 170
- DIN/ISO: G37) 172
- 7.3 Overlapping Contours 173
- 7.4 CONTOUR DATA (Cycle 20 177
- DIN/ISO: G120) 177
- DIN/ISO: G121) 179
- 7.6 ROUGH-OUT (Cycle 22 181
- DIN/ISO: G122) 181
- DIN/ISO: G123) 184
- DIN/ISO: G124) 186
- 7.9 CONTOUR TRAIN (Cycle 25 188
- DIN/ISO: G125) 188
- 7.10 Programming Examples 191
- Cylindrical Surface 197
- 8.1 Fundamentals 198
- DIN/ISO: G127, Software 199
- Option 1) 199
- Software-Option 1) 202
- (Cycle 28, DIN/ISO: G128 202
- Cycle run 205
- 8.5 Programming Examples 208
- Fixed Cycles: Contour 213
- Pocket with Contour 213
- Fundamentals 214
- Defining contour descriptions 216
- Overlapping contours 218
- Multipass Milling 227
- 10.1 Fundamentals 228
- 10.2 MULTIPASS MILLING 229
- (Cycle 230, DIN/ISO: G230) 229
- DIN/ISO: G232) 235
- 10.5 Programming Examples 240
- Cycles: Coordinate 243
- Transformations 243
- 11.1 Fundamentals 244
- 11.2 DATUM SHIFT (Cycle 7 245
- DIN/ISO: G54) 245
- 11.3 DATUM SHIFT with Datum 246
- Editing mode of operation 249
- Configuring the datum table 250
- To exit a datum table 250
- Status displays 250
- DIN/ISO: G247) 251
- 11.5 MIRROR IMAGE (Cycle 8 252
- DIN/ISO: G28) 252
- 11.6 ROTATION (Cycle 10 254
- DIN/ISO: G73) 254
- 11.7 SCALING (Cycle 11 256
- DIN/ISO: G72) 256
- 11.8 AXIS-SPECIFIC SCALING 258
- (Cycle 26) 258
- DIN/ISO: G80, Software 260
- Resetting 261
- Workspace monitoring 264
- 11.10 Programming Examples 266
- Cycles: 269
- Special Functions 269
- 12.1 Fundamentals 270
- 12.2 DWELL TIME (Cycle 9 271
- DIN/ISO: G04) 271
- 12.3 PROGRAM CALL (Cycle 12 272
- DIN/ISO: G39) 272
- 12.4 SPINDLE ORIENTATION 274
- (Cycle 13, DIN/ISO: G36) 274
- 12.5 TOLERANCE (Cycle 32 275
- DIN/ISO: G62) 275
- CAM TNCPP 276
- Cycles: Turning 279
- 13.1 Turning Cycles 280
- (Software Option 50) 280
- Working with turning cycles 282
- 13.2 ADAPT ROTARY COORDINATE 283
- SYSTEM (Cycle 800) 283
- 13.3 RESET ROTARY COORDINATE 285
- SYSTEM (Cycle 801) 285
- 13.4 Fundamentals of Turning 286
- 13.5 TURN SHOULDER 287
- LONGITUDINAL (Cycle 811) 287
- Finishing cycle run 288
- 13.6 TURN SHOULDER 290
- LONGITUDINAL EXTENDED 290
- (Cycle 812) 290
- 13.7 TURN, LONGITUDINAL 294
- PLUNGE (Cycle 813) 294
- 13.8 TURN, LONGITUDINAL 298
- PLUNGE EXTENDED 298
- (Cycle 814) 298
- 13.9 TURN CONTOUR 302
- LONGITUDINAL (Cycle 810) 302
- 13.10 TURN CONTOUR-PARALLEL 306
- (Cycle 815) 306
- 13.11 TURN SHOULDER FACE 310
- (Cycle 821) 310
- 13.12 TURN SHOULDER FACE 313
- EXTENDED (Cycle 822) 313
- (Cycle 823) 317
- EXTENDED (Cycle 824) 321
- 13.15 TURN CONTOUR 325
- TRANSVERSE (Cycle 820) 325
- 13.16 RADIAL RECESSING 329
- (Cycle 861) 329
- 13.17 RADIAL RECESSING 332
- EXTENDED (Cycle 862) 332
- 13.18 RECESSING CONTOUR 336
- RADIAL (Cycle 860) 336
- Application 340
- Roughing cycle run 340
- 13.20 AXIAL RECESSING 343
- EXTENDED (Cycle 872) 343
- (Cycle 870) 347
- 13.22 LONGITUDINAL THREAD 351
- (Cycle 831) 351
- 13.23 THREAD EXTENDED 355
- (Cycle 832) 355
- 13.24 CONTOUR-PARALLEL 359
- THREAD (Cycle 830) 359
- 13.25 Example program 363
- Using Touch Probe 367
- Touch Probe Cycles 368
- Executing touch probe cycles 373
- 14.3 Touch Probe Table 374
- Touch Probe Cycles: 377
- Automatic Measurement 377
- Misalignment 377
- 15.1 Fundamentals 378
- DIN/ISO: G400) 380
- 15.3 BASIC ROTATION from Two 383
- Q268 Q270 387
- DIN/ISO: G403) 390
- 15.6 SET BASIC ROTATION 392
- (Cycle 404, DIN/ISO: G404) 392
- (Cycle 405, DIN/ISO: G405) 394
- Automatic Datum 399
- 16.1 Fundamentals 400
- 16.2 SLOT CENTER REF PT 403
- (Cycle 408, DIN/ISO: G408) 403
- 16.3 DATUM RIDGE CENTER 407
- (Cycle 409, DIN/ISO: G409) 407
- SET_UP(TCHPROBE.TP) 420
- (Cycle 417, DIN/ISO: G417) 439
- 16.13 DATUM IN ONE AXIS 445
- (Cycle 419, DIN/ISO: G419) 445
- 0 BEGIN PGM CYC413 MM 448
- 1 TOOL CALL 69 Z 448
- Automatic Workpiece 453
- Inspection 453
- 17.1 Fundamentals 454
- 17.2 REF. PLANE (Cycle 0 460
- DIN/ISO: G55) 460
- 17.3 POLAR REFERENCE PLANE 461
- (Cycle 1) 461
- DIN/ISO: G420) 463
- 17.9 MEASURE INSIDE WIDTH 482
- (Cycle 425, DIN/ISO: G425) 482
- 17.10 MEASURE RIDGE WIDTH 485
- (Cycle 426, DIN/ISO: G426) 485
- 17.11 MEASURE COORDINATE 488
- (Cycle 427, DIN/ISO: G427) 488
- 17.14 Programming Examples 498
- 18.1 Fundamentals 504
- 18.2 MEASURING (Cycle 3) 505
- Automatic Kinematics 507
- Measurement 507
- Overview 508
- 19.2 Prerequisites 509
- DIN/ISO: G450; Option) 510
- Log function 511
- Notes on data management 512
- 19.4 MEASURE KINEMATICS 513
- (Cycle 451, DIN/ISO: G451; 513
- Positioning direction 515
- Notes on the accuracy 518
- Backlash 519
- Various modes (Q406) 524
- Automatic Tool 527
- 20.1 Fundamentals 528
- DIN/ISO: G480) 533
- (Cycle 31 or 481 534
- DIN/ISO: G481) 534
- (Cycle 32 or 482 536
- DIN/ISO: G482) 536
- Radius (Cycle 33 or 483 538
- DIN/ISO: G483) 538
- Overview 541
- Touch probes from HEIDENHAIN 549
Related products and manuals for Equipment Heidenhain TNC 640 (34059x-01) Cycle programming
(549 pages)
(549 pages)
(547 pages)
(531 pages)
(519 pages)
(678 pages)© 2020, manymanuals.com. All rights reserved. | 0.053 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals