Heidenhain TNC 320 (77185x-01) Cycle programming User Manual Page 316
- Page / 445
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Touch Probe Cycles: Automatic Datum Setting
15.2 DATUM SLOT CENTER (Cycle 408, DIN/ISO: G408)
15
316
TNC 320 | User's Manual Cycle Programming | 3/2014
15.2 DATUM SLOT CENTER (Cycle 408, DIN/
ISO: G408)
Cycle run
Touch Probe Cycle 408 finds the center of a slot and defines its
center as datum. If desired, the TNC can also enter the coordinates
into a datum table or the preset table.
1 Following the positioning logic, the TNC positions the touch
probe at rapid traverse (value from FMAX column) (see
"Executing touch probe cycles", page 286) to touch point 1. The
TNC calculates the touch points from the data in the cycle and
the safety clearance from the SET_UP column of the touch
probe table.
2 Then the touch probe moves to the entered measuring height
and runs the first probing process at the probing feed rate
(column F).
3 Then the touch probe moves either paraxially at measuring
height or at clearance height to the next starting point 2 and
probes the second touch point.
4 Finally the TNC returns the touch probe to the clearance height
and processes the determined datum depending on the cycle
parameters Q303 and Q305 (see "") and saves the actual values
in the Q parameters listed below.
5 If desired, the TNC subsequently measures the datum in the
touch probe axis in a separate probing.
Parameter number Meaning
Q166 Actual value of measured slot width
Q157 Actual value of the centerline
- User’s Manual 1
- Cycle Programming 1
- About this Manual 4
- Intended place of operation 7
- Legal information 7
- Fundamentals 10
- Contents 11
- Overviews 39
- 1.1 Introduction 40
- Available Cycle Groups 1.2 41
- 1.2 Available Cycle Groups 41
- Using Fixed Cycles 43
- 2.1 Working with fixed cycles 44
- Working with fixed cycles 2.1 45
- Using GLOBAL DEF information 49
- Global data valid everywhere 49
- Using PATTERN DEF 53
- Defining a single row 53
- Defining a single pattern 55
- Defining a full circle 57
- Defining a pitch circle 57
- 2.4 Point tables 58
- Point tables 2.4 59
- Drilling 63
- Fixed Cycles: Drilling 64
- 3.1 Fundamentals 64
- DRILLING (Cycle 200) 3.3 67
- 3.3 DRILLING (Cycle 200) 67
- ISO: G203) 74
- ISO: G205) 80
- 3.9 BORE MILLING (Cycle 208) 84
- BORE MILLING (Cycle 208) 3.9 85
- (Cycle 241, DIN/ISO: G241) 86
- Programming Examples 3.11 89
- 3.11 Programming Examples 89
- Tapping / Thread 93
- 4.1 Fundamentals 94
- (Cycle 206, DIN/ISO: G206) 95
- ISO: G207) 98
- 209, DIN/ISO: G209) 99
- Cycle parameters 101
- Prerequisites 103
- Cycle run 105
- (Cycle 263, DIN/ISO:G263) 109
- 264, DIN/ISO: G264) 113
- Q359 (incremental): 116
- (Cycle 265, DIN/ISO: G265) 117
- DIN/ISO: G267) 121
- Programming Examples 4.11 125
- 4.11 Programming Examples 125
- Fixed cycles: 127
- Pocket milling / 127
- 5.1 Fundamentals 128
- DIN/ISO: G251) 129
- ISO: G252) 133
- DIN/ISO: G256) 146
- 5.8 Programming Examples 154
- Programming Examples 5.8 155
- Fixed Cycles: 157
- Pattern Definitions 157
- 6.1 Fundamentals 158
- 6.4 Programming Examples 164
- Programming Examples 6.4 165
- Contour Pocket 167
- Fixed Cycles: Contour Pocket 168
- 7.1 SL Cycles 168
- SL Cycles 7.1 169
- Superimposed contours 7.3 171
- 7.3 Superimposed contours 171
- ISO G275) 186
- 7.11 Programming Examples 190
- Programming Examples 7.11 191
- Cylindrical Surface 195
- 8.1 Fundamentals 196
- Cycle call 197
- 8.5 Programming Examples 206
- Programming Examples 8.5 207
- Defining contour descriptions 212
- Superimposed contours 214
- Contour description programs: 219
- Multipass Milling 223
- 10.1 Fundamentals 224
- ISO: G230) 225
- Q236=+25 ;4TH POINT 3RD AXIS 230
- Q240=40 ;NUMBER OF CUTS 230
- Q207=500 ;FEED RATE FOR 230
- 10.6 Programming Examples 242
- Cycles: Coordinate 243
- Transformations 243
- 11.1 Fundamentals 244
- (Cycle 7, DIN/ISO: G53) 246
- Configuring the datum table 250
- To exit a datum table 250
- Status displays 250
- G80, software option 1) 258
- Resetting 259
- Workspace monitoring 261
- 11.10 Programming Examples 264
- Programming Examples 11.10 265
- Cycles: Special 267
- Functions 267
- Cycles: Special Functions 268
- 12.1 Fundamentals 268
- Function 269
- ISO: G36) 272
- Cycle function 273
- 12.6 ENGRAVING (Cycle 225 276
- DIN/ISO: G225) 276
- Using Touch Probe 279
- Using Touch Probe Cycles 280
- Probe Cycles 283
- Multiple measurements 285
- Touch probe table 13.3 287
- 13.3 Touch probe table 287
- Touch Probe 289
- Cycles: Automatic 289
- Measurement 289
- Misalignment 289
- 14.1 Fundamentals 290
- Fundamentals 14.1 291
- (Cycle 401, DIN/ISO: G401) 295
- (Cycle 402, DIN/ISO: G402) 298
- ISO: G403) 302
- ISO: G404) 304
- (Cycle 405, DIN/ISO: G405) 306
- Datum Setting 311
- 15.1 Fundamentals 312
- Fundamentals 15.1 313
- ISO: G408) 316
- DIN/ISO: G409) 320
- (Cycle 410, DIN/ISO: G410) 323
- Q384=+0 ;3RD CO. FOR TS AXIS 326
- Q333=+1 ;DATUM 326
- ISO: G411) 327
- 15.5 DATUM FROM OUTSIDE OF 327
- RECTANGLE (Cycle 411, DIN/ 327
- (Cycle 412, DIN/ISO: G412) 330
- (Cycle 413, DIN/ISO: G413) 335
- (Cycle 414, DIN/ISO: G414) 339
- (Cycle 415, DIN/ISO: G415) 344
- DIN/ISO: G416) 348
- Q382=+85 ;1ST CO. FOR TS AXIS 351
- Q383=+50 ;2ND CO. FOR TS AXIS 351
- Q320=0 ;SET-UP CLEARANCE 351
- 417, DIN/ISO: G417) 352
- 418, DIN/ISO: G418) 354
- ISO: G419) 358
- Workpiece 365
- Inspection 365
- 16.1 Fundamentals 366
- Fundamentals 16.1 367
- DIN/ISO: G422) 380
- 16.7 MEASURE RECTANGLE INSIDE 383
- (Cycle 423, DIN/ISO: G423) 383
- (Cycle 424, DIN/ISO: G424) 386
- DIN/ISO: G425) 389
- DIN/ISO: G426) 392
- DIN/ISO: G427) 395
- (Cycle 430, DIN/ISO: G430) 398
- Q309=0 ;PGM STOP IF ERROR 400
- Q330=0 ;TOOL 400
- 16.14 Programming Examples 404
- Programming Examples 16.14 405
- 17.1 Fundamentals 408
- MEASURE (Cycle 3) 17.2 409
- 17.2 MEASURE (Cycle 3) 409
- DIN/ISO: G461) 417
- 462, DIN/ISO: G462) 418
- (Cycle 463, DIN/ISO: G463) 420
- Tool Measurement 423
- 18.1 Fundamentals 424
- Fundamentals 18.1 425
- Tables of Cycles 439
- 19.1 Overview 440
- Overview 19.1 441
- Touch probes from HEIDENHAIN 445
Related products and manuals for Equipment Heidenhain TNC 320 (77185x-01) Cycle programming
(601 pages)
Equipment Heidenhain TNC 406 User Manual
(289 pages)
(289 pages)
Equipment Heidenhain TNC 406 User Manual
(289 pages)
(289 pages)
Equipment Heidenhain TNC 406 User Manual
(289 pages)
(289 pages)
Equipment Heidenhain TNC 410 User Manual
(319 pages)
(319 pages)
Equipment Heidenhain TNC 410 User Manual
(319 pages)
(319 pages)
Equipment Heidenhain TNC 410 User Manual
(319 pages)
(319 pages)
Equipment Heidenhain TNC 410 User Manual
(317 pages)
(317 pages)
Equipment Heidenhain TNC 410 User Manual
(319 pages)
(319 pages)
© 2020, manymanuals.com. All rights reserved. | 0.071 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals