Heidenhain TNC 320 (77185x-01) Cycle programming User Manual Page 145
- Page / 445
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
CIRCULAR SLOT (Cycle 254, DIN/ISO: G254) 5.5
5
TNC 320 | User's Manual Cycle Programming | 3/2014
145
Coordinate of workpiece surface Q203 (absolute):
Coordinate of the workpiece surface. Input range
-99999.9999 to 99999.9999
2nd set-up clearance Q204 (incremental):
Coordinate in the spindle axis at which no collision
between tool and workpiece (fixtures) can occur.
Input range 0 to 99999.9999; alternatively PREDEF
Plunging strategy Q366: Type of plunging strategy:
0: vertical plunging. The plunging angle (ANGLE) in
the tool table is not evaluated.
1, 2: reciprocal plunging. In the tool table, the
plunging angle ANGLE for the active tool must be
defined as not equal to 0. Otherwise, the TNC
generates an error message
PREDEF: The TNC uses the value from the GLOBAL
DEF block
Feed rate for finishing Q385: Traversing speed of
the tool during side and floor finishing in mm/min.
Input range 0 to 99999.999; alternatively FAUTO,
FU, FZ
Q351=+1 ;CLIMB OR UP-CUT
Q201=-20 ;DEPTH
Q202=5 ;PLUNGING DEPTH
Q369=0.1 ;ALLOWANCE FOR
FLOOR
Q206=150 ;FEED RATE FOR
PLNGNG
Q338=5 ;INFEED FOR FINISHING
Q200=2 ;SET-UP CLEARANCE
Q203=+0 ;SURFACE COORDINATE
Q204=50 ;2ND SET-UP
CLEARANCE
Q366=1 ;PLUNGE
Q385=500 ;FINISHING FEED RATE
9 L X+50 Y+50 R0 FMAX M3 M99
- User’s Manual 1
- Cycle Programming 1
- About this Manual 4
- Intended place of operation 7
- Legal information 7
- Fundamentals 10
- Contents 11
- Overviews 39
- 1.1 Introduction 40
- Available Cycle Groups 1.2 41
- 1.2 Available Cycle Groups 41
- Using Fixed Cycles 43
- 2.1 Working with fixed cycles 44
- Working with fixed cycles 2.1 45
- Using GLOBAL DEF information 49
- Global data valid everywhere 49
- Using PATTERN DEF 53
- Defining a single row 53
- Defining a single pattern 55
- Defining a full circle 57
- Defining a pitch circle 57
- 2.4 Point tables 58
- Point tables 2.4 59
- Drilling 63
- Fixed Cycles: Drilling 64
- 3.1 Fundamentals 64
- DRILLING (Cycle 200) 3.3 67
- 3.3 DRILLING (Cycle 200) 67
- ISO: G203) 74
- ISO: G205) 80
- 3.9 BORE MILLING (Cycle 208) 84
- BORE MILLING (Cycle 208) 3.9 85
- (Cycle 241, DIN/ISO: G241) 86
- Programming Examples 3.11 89
- 3.11 Programming Examples 89
- Tapping / Thread 93
- 4.1 Fundamentals 94
- (Cycle 206, DIN/ISO: G206) 95
- ISO: G207) 98
- 209, DIN/ISO: G209) 99
- Cycle parameters 101
- Prerequisites 103
- Cycle run 105
- (Cycle 263, DIN/ISO:G263) 109
- 264, DIN/ISO: G264) 113
- Q359 (incremental): 116
- (Cycle 265, DIN/ISO: G265) 117
- DIN/ISO: G267) 121
- Programming Examples 4.11 125
- 4.11 Programming Examples 125
- Fixed cycles: 127
- Pocket milling / 127
- 5.1 Fundamentals 128
- DIN/ISO: G251) 129
- ISO: G252) 133
- DIN/ISO: G256) 146
- 5.8 Programming Examples 154
- Programming Examples 5.8 155
- Fixed Cycles: 157
- Pattern Definitions 157
- 6.1 Fundamentals 158
- 6.4 Programming Examples 164
- Programming Examples 6.4 165
- Contour Pocket 167
- Fixed Cycles: Contour Pocket 168
- 7.1 SL Cycles 168
- SL Cycles 7.1 169
- Superimposed contours 7.3 171
- 7.3 Superimposed contours 171
- ISO G275) 186
- 7.11 Programming Examples 190
- Programming Examples 7.11 191
- Cylindrical Surface 195
- 8.1 Fundamentals 196
- Cycle call 197
- 8.5 Programming Examples 206
- Programming Examples 8.5 207
- Defining contour descriptions 212
- Superimposed contours 214
- Contour description programs: 219
- Multipass Milling 223
- 10.1 Fundamentals 224
- ISO: G230) 225
- Q236=+25 ;4TH POINT 3RD AXIS 230
- Q240=40 ;NUMBER OF CUTS 230
- Q207=500 ;FEED RATE FOR 230
- 10.6 Programming Examples 242
- Cycles: Coordinate 243
- Transformations 243
- 11.1 Fundamentals 244
- (Cycle 7, DIN/ISO: G53) 246
- Configuring the datum table 250
- To exit a datum table 250
- Status displays 250
- G80, software option 1) 258
- Resetting 259
- Workspace monitoring 261
- 11.10 Programming Examples 264
- Programming Examples 11.10 265
- Cycles: Special 267
- Functions 267
- Cycles: Special Functions 268
- 12.1 Fundamentals 268
- Function 269
- ISO: G36) 272
- Cycle function 273
- 12.6 ENGRAVING (Cycle 225 276
- DIN/ISO: G225) 276
- Using Touch Probe 279
- Using Touch Probe Cycles 280
- Probe Cycles 283
- Multiple measurements 285
- Touch probe table 13.3 287
- 13.3 Touch probe table 287
- Touch Probe 289
- Cycles: Automatic 289
- Measurement 289
- Misalignment 289
- 14.1 Fundamentals 290
- Fundamentals 14.1 291
- (Cycle 401, DIN/ISO: G401) 295
- (Cycle 402, DIN/ISO: G402) 298
- ISO: G403) 302
- ISO: G404) 304
- (Cycle 405, DIN/ISO: G405) 306
- Datum Setting 311
- 15.1 Fundamentals 312
- Fundamentals 15.1 313
- ISO: G408) 316
- DIN/ISO: G409) 320
- (Cycle 410, DIN/ISO: G410) 323
- Q384=+0 ;3RD CO. FOR TS AXIS 326
- Q333=+1 ;DATUM 326
- ISO: G411) 327
- 15.5 DATUM FROM OUTSIDE OF 327
- RECTANGLE (Cycle 411, DIN/ 327
- (Cycle 412, DIN/ISO: G412) 330
- (Cycle 413, DIN/ISO: G413) 335
- (Cycle 414, DIN/ISO: G414) 339
- (Cycle 415, DIN/ISO: G415) 344
- DIN/ISO: G416) 348
- Q382=+85 ;1ST CO. FOR TS AXIS 351
- Q383=+50 ;2ND CO. FOR TS AXIS 351
- Q320=0 ;SET-UP CLEARANCE 351
- 417, DIN/ISO: G417) 352
- 418, DIN/ISO: G418) 354
- ISO: G419) 358
- Workpiece 365
- Inspection 365
- 16.1 Fundamentals 366
- Fundamentals 16.1 367
- DIN/ISO: G422) 380
- 16.7 MEASURE RECTANGLE INSIDE 383
- (Cycle 423, DIN/ISO: G423) 383
- (Cycle 424, DIN/ISO: G424) 386
- DIN/ISO: G425) 389
- DIN/ISO: G426) 392
- DIN/ISO: G427) 395
- (Cycle 430, DIN/ISO: G430) 398
- Q309=0 ;PGM STOP IF ERROR 400
- Q330=0 ;TOOL 400
- 16.14 Programming Examples 404
- Programming Examples 16.14 405
- 17.1 Fundamentals 408
- MEASURE (Cycle 3) 17.2 409
- 17.2 MEASURE (Cycle 3) 409
- DIN/ISO: G461) 417
- 462, DIN/ISO: G462) 418
- (Cycle 463, DIN/ISO: G463) 420
- Tool Measurement 423
- 18.1 Fundamentals 424
- Fundamentals 18.1 425
- Tables of Cycles 439
- 19.1 Overview 440
- Overview 19.1 441
- Touch probes from HEIDENHAIN 445
Related products and manuals for Equipment Heidenhain TNC 320 (77185x-01) Cycle programming
(601 pages)
Equipment Heidenhain TNC 406 User Manual
(289 pages)
(289 pages)
Equipment Heidenhain TNC 406 User Manual
(289 pages)
(289 pages)
Equipment Heidenhain TNC 406 User Manual
(289 pages)
(289 pages)
Equipment Heidenhain TNC 410 User Manual
(319 pages)
(319 pages)
Equipment Heidenhain TNC 410 User Manual
(319 pages)
(319 pages)
Equipment Heidenhain TNC 410 User Manual
(319 pages)
(319 pages)
Equipment Heidenhain TNC 410 User Manual
(317 pages)
(317 pages)
Equipment Heidenhain TNC 410 User Manual
(319 pages)
(319 pages)
© 2020, manymanuals.com. All rights reserved. | 0.050 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals