Heidenhain TNC 320 (34055x-06) Cycle programming User Manual Page 159
- Page / 403
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Superimposed contours 7.3
7
TNC 320 | User's Manual Cycle Programming | 5/2013
159
Surface B:
56 LBL 2
57 L X+40 Y+50 RL
58 CC X+65 Y+50
59 C X+40 Y+50 DR-
60 LBL 0
Area of intersection
Only the area where A and B overlap is to be machined. (The areas
covered by A or B alone are to be left unmachined.)
A and B must be pockets.
A must start inside of B.
Surface A:
51 LBL 1
52 L X+60 Y+50 RR
53 CC X+35 Y+50
54 C X+60 Y+50 DR-
55 LBL 0
Surface B:
56 LBL 2
57 L X+90 Y+50 RR
58 CC X+65 Y+50
59 C X+90 Y+50 DR-
60 LBL 0
- User’s Manual 1
- Cycle Programming 1
- About this Manual 4
- Intended place of operation 7
- Legal information 7
- Contents 10
- Fundamentals / 37
- Overviews 37
- Fundamentals / Overviews 38
- 1.1 Introduction 38
- Available Cycle Groups 1.2 39
- 1.2 Available Cycle Groups 39
- Using Fixed Cycles 41
- 2.1 Working with fixed cycles 42
- Working with fixed cycles 2.1 43
- Using GLOBAL DEF information 47
- Global data valid everywhere 47
- Using PATTERN DEF 51
- Defining a single pattern 53
- Defining a full circle 55
- Defining a pitch circle 55
- 2.4 Point tables 56
- Point tables 2.4 57
- Drilling 59
- Fixed Cycles: Drilling 60
- 3.1 Fundamentals 60
- DRILLING (Cycle 200) 3.3 63
- 3.3 DRILLING (Cycle 200) 63
- ISO: G203) 70
- ISO: G205) 76
- BORE MILLING (Cycle 208) 3.9 79
- 3.9 BORE MILLING (Cycle 208) 79
- DIN/ISO: G241) 81
- 3.11 Programming Examples 84
- Programming Examples 3.11 85
- Tapping / Thread 87
- 4.1 Fundamentals 88
- ISO: G207) 92
- 209, DIN/ISO: G209) 93
- Prerequisites 97
- Cycle parameters 101
- (Cycle 263, DIN/ISO:G263) 102
- 264, DIN/ISO: G264) 105
- (Cycle 265, DIN/ISO: G265) 108
- DIN/ISO: G267) 112
- 4.11 Programming Examples 115
- Programming Examples 4.11 115
- Fixed Cycles: 117
- Pocket Milling / 117
- Stud Milling / Slot 117
- 5.1 Fundamentals 118
- DIN/ISO: G251) 119
- ISO: G252) 123
- Cycle run 127
- ISO: G256) 136
- Programming Examples 5.8 143
- 5.8 Programming Examples 143
- Pattern Definitions 145
- 6.1 Fundamentals 146
- ISO: G220) 147
- Programming Examples 6.4 151
- 6.4 Programming Examples 151
- Contour Pocket 153
- Fixed Cycles: Contour Pocket 154
- 7.1 SL Cycles 154
- SL Cycles 7.1 155
- Superimposed contours 7.3 157
- 7.3 Superimposed contours 157
- 7.10 Programming Examples 172
- Programming Examples 7.10 173
- Cylindrical Surface 177
- 8.1 Fundamentals 178
- ISO: G127, software option 1) 179
- 8.5 Programming Examples 188
- Programming Examples 8.5 189
- Fundamentals 192
- Defining contour descriptions 194
- Superimposed contours 196
- Contour description programs: 201
- Multipass Milling 205
- 10.1 Fundamentals 206
- ISO: G230) 207
- Programming Examples 10.5 217
- 10.5 Programming Examples 217
- Cycles: Coordinate 219
- Transformations 219
- 11.1 Fundamentals 220
- (Cycle 7, DIN/ISO: G53) 222
- Editing mode of operation 224
- Configuring the datum table 225
- To exit a datum table 225
- Status displays 225
- G80, software option 1) 232
- Resetting 233
- Workspace monitoring 235
- 11.10 Programming Examples 238
- Programming Examples 11.10 239
- Cycles: Special 241
- Functions 241
- Cycles: Special Functions 242
- 12.1 Fundamentals 242
- Function 243
- ISO: G36) 245
- ISO: G225) 249
- Allowed engraving characters 251
- Engraving system variables 251
- Using Touch Probe 253
- Using Touch Probe Cycles 254
- Probe Cycles 257
- Executing touch probe cycles 259
- 13.3 Touch probe table 260
- Touch probe table 13.3 261
- Touch Probe 263
- Cycles: Automatic 263
- Measurement 263
- Misalignment 263
- 14.1 Fundamentals 264
- Fundamentals 14.1 265
- ISO: G400) 266
- (Cycle 401, DIN/ISO: G401) 268
- (Cycle 402, DIN/ISO: G402) 270
- ISO: G403) 274
- ISO: G404) 276
- (Cycle 405, DIN/ISO: G405) 278
- Datum Setting 281
- 15.1 Fundamentals 282
- Fundamentals 15.1 283
- ISO: G408) 286
- DIN/ISO: G409) 289
- (Cycle 410, DIN/ISO: G410) 292
- ISO: G411) 297
- (Cycle 412, DIN/ISO: G412) 300
- (Cycle 413, DIN/ISO: G413) 304
- (Cycle 414, DIN/ISO: G414) 308
- (Cycle 415, DIN/ISO: G415) 312
- DIN/ISO: G416) 315
- 417, DIN/ISO: G417) 318
- 418, DIN/ISO: G418) 320
- ISO: G419) 323
- Workpiece 329
- Inspection 329
- 16.1 Fundamentals 330
- Fundamentals 16.1 331
- DIN/ISO: G422) 343
- 16.7 MEASURE RECTANGLE INSIDE 346
- (Cycle 423, DIN/ISO: G423) 346
- (Cycle 424, DIN/ISO: G424) 350
- DIN/ISO: G425) 353
- DIN/ISO: G426) 356
- DIN/ISO: G427) 358
- (Cycle 430, DIN/ISO: G430) 360
- 16.14 Programming Examples 366
- Programming Examples 16.14 367
- 17.1 Fundamentals 370
- MEASURE (Cycle 3) 17.2 371
- 17.2 MEASURE (Cycle 3) 371
- DIN/ISO: G461) 377
- 462, DIN/ISO: G462) 378
- (Cycle 463, DIN/ISO: G463) 380
- Tool Measurement 383
- 18.1 Fundamentals 384
- Fundamentals 18.1 385
- ISO: G480) 388
- 484, DIN/ISO: G484) 389
- DIN/ISO: G481) 390
- DIN/ISO: G482) 392
- Tables of Cycles 397
- 19.1 Overview 398
- Overview 19.1 399
- Touch probes from HEIDENHAIN 403
Related products and manuals for Equipment Heidenhain TNC 320 (34055x-06) Cycle programming
(439 pages)
(437 pages)
(437 pages)
(463 pages)
(505 pages)
(509 pages)© 2020, manymanuals.com. All rights reserved. | 0.049 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals