Heidenhain MANUALplus 4110 Pilot User Manual Page 5
- Page / 119
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
5
Setup
Display fields for machine data
Position display
Display of the current distance between tool tip
and workpiece datum in X and Z, or the current
position of the C axis.
Distance-to-go
MANUALplus calculates the distance remaining
from the current position to the target position of
the active traversing command.
Spindle utilization
Utilization of the spindle motor
T display
• T number of the inserted tool
• Tool compensation values
F display
• Symbol for cycle status
• Upper field: programmed value
• Lower field: setting of override control and actual
feed rate
S display
• Symbol for spindle status
• Upper field: programmed value
• Lower field: setting of override control and actual
spindle speed
• With position control (M19): spindle position
• Gear range (small number next to “S“)
• “S“ highlighted: S display is valid for the driven tool
Setup
Entering machine data (“Set S, F, T“)
With “Set S, F, T“ you enter the machine data required for manual
operation, as well as the maximum speed and tool angle.
Note with driven tools:
• MANUALplus recognizes from the tool description whether a driven
tool is used.
• If the active tool is a driven tool, the displayed spindle and machine
tool data refer to the driven tool.
• Milling cutters always qualify as “driven tools“.
• After system start, MANUALplus assumes that the tool
that was last used is still inserted in the tool holder. If this
is not the case, you must inform the control of the tool
change.
• At a “constant cutting speed“, MANUALplus calculates the
spindle speed depending on the tool tip position. The smaller
the diameter of the tip, the higher the spindle speed. The
“maximum spindle speed D“, however, is never exceeded.
- MANUALplus 1
- The Pilot 3
- Contents 3
- Operation of the MANUALplus 4
- Tool Measurement 7
- Manual mode 8
- Teach-in (Cycle mode) 9
- Program run 9
- Graphic simulation 10
- Blank Bar/Tube 12
- Workpiece blank contour ICP 12
- Single cuts 13
- Circular machining 14
- Linear machining at angle 14
- Rounding 15
- Cut longitudinal 16
- Cut transverse 16
- Plunge longitudinal 17
- Plunge transverse 17
- Clearance cycle group 18
- ICP cutting longitudinal 19
- ICP cutting transverse 19
- Recessing radial 20
- Recessing axial 20
- ICP recessing radial 21
- ICP recessing axial 21
- Recess turning radial 22
- Recess turning axial 22
- ICP recess turning radial 23
- ICP recess turning axial 23
- Undercut H 24
- Undercut K 24
- Undercut U 25
- Threadcut cycle group 26
- Tapered thread 28
- API thread 28
- Thread undercut DIN 76 29
- Undercut DIN 509 E 29
- Undercut DIN 509 F 29
- Drilling axial 30
- Drilling radial 30
- Deep-drilling (pecking) axial 31
- Tapping axial 32
- Tapping radial 32
- Thread milling axial 33
- Groove axial 34
- Groove radial 34
- Rapid traverse positioning 34
- Figure axial 35
- Figure radial 35
- ICP figure axial 36
- ICP figure radial 36
- Face milling 37
- Helical groove milling 38
- Pattern linear axial 39
- Pattern circular axial 40
- Pattern linear radial 41
- Pattern circular radial 42
- DIN Cycle 43
- ICP Programming 44
- ICP Contour Elements 45
- DIN Programming 48
- Overview of G Commands 49
- Chuck part, cylinder/tube G20 51
- Workpiece blank contour G21 51
- Rapid traverse G0 52
- Tool change point G14 52
- Linear path G1 53
- Circular path 54
- Feed rate, spindle speed 55
- MCRC) G40, G41, G42 56
- Corrections 57
- Zero point displacement G51 58
- Zero point displacement 59
- Oversizes 60
- Transverse roughing cycle G82 61
- End of cycle G80 61
- Line with radius G87 66
- Line with chamfer G88 66
- Contour finishing cycle G89 67
- Simple recessing cycle G86 68
- Axial contour cutting G861 69
- Radial contour cutting G862 69
- Recessing cycle 70
- Axial finishing cut G867 71
- Radial finishing cut G868 71
- Universal thread cycle G31 74
- Simple thread cycle G32 75
- Individual thread cut G33 76
- Metric ISO thread G35 77
- Tapered API thread G352 79
- Tapered thread G353 80
- Undercut contour G25 81
- Undercut cycle G85 82
- Undercut cycles 83
- Undercut Form U G856 84
- Undercut Form H G857 85
- Undercut Form K G858 85
- Cut-off cycle G859 86
- Simple drilling cycle G71 87
- Deep-hole pecking cycle G74 88
- Thread tapping cycle G36 89
- Thread milling cycle G799 90
- End-face machining 91
- Reference diameters G120 99
- Lateral-surface machining 100
- Helical groove milling G798 104
- Drilling and milling patterns 106
- Tool Management 109
- Lathe tools 110
- Recessing tools 112
- Threading tools 113
- Drilling tools 114
- Tapping tools 114
- Milling tools 115
- Workpiece Generation 116
- Cycle Overview 119
Related products and manuals for Equipment Heidenhain MANUALplus 4110 Pilot
Equipment Heidenhain MANUALplus 4110 User Manual
(553 pages)
(553 pages)
(119 pages)
(119 pages)
(13 pages)
(13 pages)
Equipment Heidenhain CNC Pilot 4290 User Manual
(481 pages)
(481 pages)
© 2020, manymanuals.com. All rights reserved. | 0.045 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals